Bell RS7 Carbon Duckbill Helmet - SA2020 / FIA8859
BEL1204A06 (1 in stock)Bell Helmets
Regular price
$1,499.95
Featuring an ultra-lightweight carbon shell, the Bell RS7 Carbon Duckbill Helmet offers unmatched comfort, aerodynamic performance, and energy-absorbing capability. The advanced ventilation system includes 14 air intake and extraction channels for unsurpassed air flow and ventilation. This helmet is also offered in a non-duckbill version. Both duckbill and non-duckbill styles have a natural carbon finish.
- Ultra-lightweight carbon shell
- Advanced multi-density, multi-piece liner to maximize energy absorption and impact performance
- Optical grade injection molded Double Screen Anti-Fog (DSAF) visor for anti-fog control and superior visibility
- Powerful and effective top and chin bar ventilation system with 14 air intake and extraction channels for maximum ventilation
- Air intake system includes two-part center and side air intakes (installed)
- Shell and shield design optimized to improve aerodynamic performance, reduce internal noise, and enhance energy management capacities
- Integrated channels in face piece offer multiple options to install drink tube and radio systems
- Duckbill (chin spoiler)
- Rear spoilers, top gurneys, and chin bar gurneys available separately
- Forced air attachments available separately
- Factory installed Hans anchors as original equipment
- Synthetic rubber gasket seal to prevent dirt and water from entering the helmet
- Shield and pivot kit: SE07 3mm, SV(SE07, SE077)
- Color: Carbon
- Natural carbon finish
- Sizes: 6 3/4 (54) to 7 5/8+ (61+)
- Uses SE-07 shields
- Snell SA2020 and FIA approved
Includes:
- RS7 Carbon
- Clear SE07 3mm DSAF Shield Installed
- Draw String Helmet Bag
- Hans Post Anchors Installed
- Plastic Tearoff Posts Installed
- Hex Wrench Key
Attributes
|
Product Line
|
RS7
|
|
Open/Closed Face
|
Closed
|
|
Fresh Air
|
No
|
|
Vent System
|
Yes
|
|
Snell Rating
|
SA 2020
|
|
FIA Approved
|
Yes
|
|
Head and Neck Support Ready
|
Yes
|
|
Shield Included
|
Yes
|
|
Shield Color
|
Clear
|
|
Visor Included
|
No
|
|
Graphics
|
No
|
|
Bag Included
|
Yes
|
|
Gloss/Flat
|
Gloss
|
|
Material
|
Carbon Fiber
|
|
Color
|
Natural
|
|
Finish
|
Clearcoat
|
|
Quantity
|
Each
|
Available in the following sizes:
| MPN | Size |
| 1204A06 | 7-1/8 Minus (57 cm) |
| 1204A07 | 7-1/4 (58 cm) |
| 1204A08 | 7-3/8 (59 cm) |
| 1204A09 | 7-3/8+ 59+ cm) |
| 1204A10 | 7-1/2 (60 cm) |
| 1204A11 | 7-5/8 (61 cm) |
Size Chart
Bell Helmet Size Chart
| Size | Hat Size | Inches | Centimeters |
|---|---|---|---|
| 4XS | 6 3/8 | 20 1/16 | 51 |
| 3XS | 6 1/2 - 6 5/8 | 20 1/2 - 20 7/8 | 52-53 |
| 2XS | 6 3/4 - 6 7/8 | 21 1/2 - 21 5/8 | 54-55 |
| XS | 7 | 22 | 56 |
| S | 7 1/8 | 22 3/8 | 57 |
| M | 7 1/4 - 7 3/8 | 22 3/4 - 23 1/4 | 58-59 |
| L | 7 1/2 | 23 5/8 | 60 |
| XL | 7 5/8 - 7 3/4 | 24 - 24 3/8 | 61-62 |
| 2XL | 7 7/8 - 8 | 24 3/4 - 25 1/4 | 63-64 |
| 3XL | 8 1/8 - 8 1/4 | 25 5/8 - 26 | 65-66 |
| 4XL | 8 3/8 - 8 1/2 | 26 3/8 - 26 3/4 | 67-68 |
Fitting your Bell Helmet
Proper helmet fit is vital to the performance of a helmet during an impact. For maximum protection the helmet must fit properly with the chin strap securely fastened and provide adequate peripheral vision.
Measuring the head is only a starting point for the entire sizing procedure. Due to varying shapes, heads that are apparently the same size when measured by a tape may not necessarily fit the same size helmet. A small metal tape measure or a cloth tape may be used to make your initial measurement. You can also use a string, which can then be laid against a measuring tape.
The circumference of the head should be measured at a point approximately one inch above the eyebrows in front, and at a point in the back of the head that results in the largest possible measurement. Take several measurements. The largest measurement is the one you want to try on first. If you use a balaclava or head sock, always measure and fit the helmet with it on. Use the Bell sizing chart to determine the size that best matches the head measurement.